Reply to thread

Message

Good Day.
This past week has been productive on the modeling front.
Working slowly from the back towards the front, I got the frame around the sensor dish array installed. I did have to cut it back a little bit at the forward end, as it was slightly over size.

[ATTACH=full]81640[/ATTACH]

With the frame in, it was time to work on constructing the sensor dish.
This was straight forward and no issues.

[ATTACH=full]81641[/ATTACH]

[ATTACH=full]81642[/ATTACH]

Then on to installing the array. First gluing the base down, then attaching the sides from the back towards the front. The little bit of overhang on the front was trimmed back after it dried.

[ATTACH=full]81643[/ATTACH]

[ATTACH=full]81644[/ATTACH]

The last part to assemble and install on this section of the secondary hull was the forward torpedo bay and the Captain's Gig.

[ATTACH=full]81645[/ATTACH]

[ATTACH=full]81646[/ATTACH]

[ATTACH=full]81647[/ATTACH]

[ATTACH=full]81648[/ATTACH]

[ATTACH=full]81649[/ATTACH]

[ATTACH=full]81650[/ATTACH]

This completes the bottom of the secondary hull. Now on to the top half.

Thank you for following.
Questions and comments welcome.

Jim

<blockquote data-quote="Papermodder" data-source="post: 198897" data-attributes="member: 12832">Good Day.This past week has been productive on the modeling front.Working slowly from the back towards the front, I got the frame around the sensor dish array installed. I did have to cut it back a little bit at the forward end, as it was slightly over size.[ATTACH=full]81640[/ATTACH]With the frame in, it was time to work on constructing the sensor dish.This was straight forward and no issues.[ATTACH=full]81641[/ATTACH][ATTACH=full]81642[/ATTACH]Then on to installing the array. First gluing the base down, then attaching the sides from the back towards the front. The little bit of overhang on the front was trimmed back after it dried.[ATTACH=full]81643[/ATTACH][ATTACH=full]81644[/ATTACH]The last part to assemble and install on this section of the secondary hull was the forward torpedo bay and the Captain&#039;s Gig.[ATTACH=full]81645[/ATTACH][ATTACH=full]81646[/ATTACH][ATTACH=full]81647[/ATTACH][ATTACH=full]81648[/ATTACH][ATTACH=full]81649[/ATTACH][ATTACH=full]81650[/ATTACH]This completes the bottom of the secondary hull. Now on to the top half. &nbsp;Thank you for following.Questions and comments welcome.&nbsp;Jim</blockquote>

[QUOTE="Papermodder, post: 198897, member: 12832"] Good Day. This past week has been productive on the modeling front. Working slowly from the back towards the front, I got the frame around the sensor dish array installed. I did have to cut it back a little bit at the forward end, as it was slightly over size. [ATTACH=full]81640[/ATTACH] With the frame in, it was time to work on constructing the sensor dish. This was straight forward and no issues. [ATTACH=full]81641[/ATTACH] [ATTACH=full]81642[/ATTACH] Then on to installing the array. First gluing the base down, then attaching the sides from the back towards the front. The little bit of overhang on the front was trimmed back after it dried. [ATTACH=full]81643[/ATTACH] [ATTACH=full]81644[/ATTACH] The last part to assemble and install on this section of the secondary hull was the forward torpedo bay and the Captain's Gig. [ATTACH=full]81645[/ATTACH] [ATTACH=full]81646[/ATTACH] [ATTACH=full]81647[/ATTACH] [ATTACH=full]81648[/ATTACH] [ATTACH=full]81649[/ATTACH] [ATTACH=full]81650[/ATTACH] This completes the bottom of the secondary hull. Now on to the top half. Thank you for following. Questions and comments welcome. Jim [/QUOTE]

Verification