bubbles in paint

[durangod]

What causes bubbles in paint?

I used testors red for the fan, look close at the fan, all those little dots are bubbles and they suck lol

 

[urumomo]

After zooming in , I'm pretty sure all those equally spaced dots are the fastener details on each blade .
The exception is the blob @ about the 5 o'clock position on the edge of the blade .
That looks like a solid contaminant .

 

[Motoretrolia]

Seems rather thick, was the paint older? Perhaps a drop or two of thinner might help. I don't really see bubbling although if it's there, perhaps it's due to out gassing due to a chemical reaction.

 

[BlackSheepTwoOneFour]

Both good observations why. Did you stir your paint thoroughly? Sometimes sediments settle at the bottom. Testors small square bottle paint have that tendency to settle on the bottom. I always stir and shake often when I need to use it.

 

[durangod]

yes i believe it was too thick and yes most were the bolt pattern for blade connection which are now painted. Thanks.

I also believe that there is some contamination of some kind. As @BlackSheepTwoOneFour stated. I do shake paints but dont stir them.

I say contamination because it happens with spray also. Luckily so far on places not really seen.

Examples two seats, both same primer left one is perfect, right one has bubbles on the front part of the seat at knee level (front square part). Also on the underside of cab (black) My black can was almost empty which may also be part of it, but other cans were not.

Its also possible that i do need to wash larger parts to give extra confidence that it wont happen like on a auto body part, that would be miserable to have to clean and respray.

There are also some tiny specs in the seat diamond pattern like the paint wont stick. But i plan to brush on another color for 2 tone so i think i can cover those.

 

[the Baron]

As far as air bubbles in the paint are concerned, I get them occasionally when hand-brushing, if I've thinned the paint too much. I can brush the bubbles out, and then add a touch more of the paint to the mix to make it a little thicker.

 

[BlackSheepTwoOneFour]

yes i believe it was too thick and yes most were the bolt pattern for blade connection which are now painted. Thanks.

I also believe that there is some contamination of some kind. As @BlackSheepTwoOneFour stated. I do shake paints but dont stir them.

I highly recommend you do make it a habit to stir then shake. I always do. Shaking the bottle isn't going to loosen the good stuff at the bottom of the bottle.

I say contamination because it happens with spray also. Luckily so far on places not really seen.

Highly doubt there's contamination unless you've added thinner into the bottle by accident.

Examples two seats, both same primer left one is perfect, right one has bubbles on the front part of the seat at knee level (front square part). Also on the underside of cab (black) My black can was almost empty which may also be part of it, but other cans were not.

Its also possible that i do need to wash larger parts to give extra confidence that it wont happen like on a auto body part, that would be miserable to have to clean and respray.

There are also some tiny specs in the seat diamond pattern like the paint wont stick. But i plan to brush on another color for 2 tone so i think i can cover those.

View attachment 125600View attachment 125601View attachment 125602View attachment 125603View attachment 125604

Try putting a little paint in a small pallet dish, add a little thinner especially with those Testors small square bottles. Oftentimes they tend to be thick - even brand new bottles.

 

[airdave]

Shaking paint introduces air (and bubbles) into paint, thats why it is never recommended with clears.
(spray bomb clear has such a small amount of paint in the can and a diffusing nozzle, that shaking isn't a problem)

I would think with something as thick as testor's enamels, shaking can easily trap air in such viscous paint.
And then, if you brush it on thick, those bubbles will appear.

As enamel gets older, it needs to be thinned more and more to keep it stirrable and consistent and flowing.
These is how I always worked with Testor's back in the 1970s.

 

[BarleyBop]

Because most of my paints are in these squeeze bottles, it is a pain to pull out the nozzle to stir... I started using these ball bearings and it seems to make a difference. Pop the top, plop one in, "oh what a relief it is". Then when the bottle is empty, retrieve the ball for reuse!