When im not modeling

[durangod]

Here is what i have been doing the last few days. Had a leak in the RV and had to remove the insulation and do some repairs in the wall. I removed the fiber insulation and installed foam insulation which will not absorb water. Water is deadly to an RV.

I also took the time to build a modeling paint rack and with the extra room im adding some shelves and a small peg board area.




Used to be storage cabinet on the wall but since the fake wood paper on it is peeling im going to use that for my shop and put up some shelves in its place. I also have my eye on a print (painting) to put in the framed space.

I can do plumbing, electrical, structural walls and concrete, at the handyman level. I could probably build my own home for the most part if i was in better health, but i would have to hire out for HVAC i cant do that stuff. Worked alot around construction in my life and im not a contractor by far but i have alot of mixed knowledge. One of my projects comming up is running the electrical to my new shop, and installing the sub panel myself.

 

[Rimmer]

Excellent - if you're in North wales you can come and run a power line into my shed!

It's really good being able to do that stuff. I can do woodwork and plumbing etc. but I'm not too up on electricals.

 

[durangod]

Excellent - if you're in North wales you can come and run a power line into my shed!

It's really good being able to do that stuff. I can do woodwork and plumbing etc. but I'm not too up on electricals.

im sure in wales they have a completely different electrical bible. I know the outlets across the pond are different. But i would give it a whirl We would have to test it with a toaster first so if it gets burned up, its cheap to replace. LOL

 

[durangod]

ok peg board is up and i decided to do a surround shelf.

And 12 bucks each for wooden shelf brackets and look at the cheap screws they use for the mounting bracket on the rear. I changed them out of course.

 

[TimM63]

im sure in wales they have a completely different electrical bible. I know the outlets across the pond are different. But i would give it a whirl We would have to test it with a toaster first so if it gets burned up, its cheap to replace. LOL

You don't want to plug anything from the US into a UK socket.

 

[durangod]

You don't want to plug anything from the US into a UK socket.

Is that because i dont have the insatiable craving for hot tea, only UK people can use UK sockets lol Maybe i can test one here before i go there and try it, see if i like it first lol

 

[Jakko]

You don't want to plug anything from the US into a UK socket.

Things like phone chargers and similar tend to work with no problems — they'll recognise they're getting 230 V, 50 Hz instead of 115 V, 60 Hz and adjust themselves to give the correct output.

Of course, you'll need an adapter to put the dodgy American plug into the overbuilt UK socket, but more importantly check before you do this that the text on the charger says it's rated for 240 V. Because if it's not, it will probably mean that pretty soon you get to meet the local firemen.

 

[BlackSheepTwoOneFour]

Like I said…those Brits have everything backasswards….. ROFLMAO!

 

[durangod]

Got back to modeling late the other day i took a few days away to build another shelf (this time using my router for edge, i forgot on other shelves.




i also worked up a concrete pour footing support structure for the boat engine hoist ill use to remove the engine.

before



after



it will support this

https://www.harborfreight.com/12-ton-capacity-pickup-truck-bed-crane-with-hand-winch-61522.html

last year i built a dry dock in my yard where i could lift the boat and support it while i work on it and refurbish trailer away from boat.

 

[BOATMAN]

EXCUSE ME but the uk is 240 v ratein what is it in the U/S ?
Chrisb

 

[durangod]

In the US we use 120/240 volts

 

[Jakko]

Be glad you're not in Japan, is all I'll say The whole country is 100 V, but the western half uses 60 Hz while the east half uses 50 Hz, which means you don't want to plug in, say, an alarm clock on the wrong side of the divide

 

[the Baron]

"220, 221. Whatever it takes."

 

[plastickjunkie]

Currently working on the wife's to do list. Almost done doing wall panel molding. Caulking and paint to follow. The molding on the right in the picture been painted in the wall color blending in with a subtle look. It's very easy to do and adds a rich fancy look to the room. I have another smaller wall to go to finish this project. Sorry for the mess but I need the space to work behind the furniture.

 

[BarleyBop]

Here is what i have been doing the last few days.

I can do plumbing, electrical, structural walls and concrete, at the handyman level....

Very nice. Isn't it satisfying to do that stuff? I've learned a thing or two over the years as well.
In my province, you can do just about anything, with a permit, and an inspection. Even electrical and plumbing. For the most part, common sense and care.
I learned from helping others, uncles and brothers-in-law, and books.
These days there are videos for everything, but I find that videos don't give you experience, or the hard knowledge gained of figuring things out on your own.
Small, scalable skills are just that... in the end it is all about time, cost, and having the health/energy to do it.
A bit of patience, a bit of planning, a lot of not freaking out when things go sideways.

Just like model building!!

 

[BarleyBop]

Be glad you're not in Japan, is all I'll say The whole country is 100 V, but the western half uses 60 Hz while the east half uses 50 Hz, which means you don't want to plug in, say, an alarm clock on the wrong side of the divide

...the wrong side... reminds me if the story of the two fellas installing wallboard. One of them was throwing every other screw on the floor... so the first guy says to him: "why are ya doing that?", to which the fella replies: "well, the screws are facing the wrong way!"
Somewhat annoyed, the first guy says: " You idiot! Save 'em for the wall behind us!"

 

[Sweet-Chuck]

Very nice. Isn't it satisfying to do that stuff? I've learned a thing or two over the years as well.
In my provinc
m helping others, uncles and brothers-in-law, and books.

T

Currently working on the wife's to do list. Almost done doing wall panel molding. Caulking and paint to follow. The molding on the right in the picture been painted in the wall color blending in with a subtle look. It's very easy to do and adds a rich fancy look to the room. I have another smaller wall to go to finish this project. Sorry for the mess but I need the space to work behind the furniture.
View attachment 132786

Just like model building!!

View attachment 132786

Did a similar upgrade a couple years ago in our living room-wainscotting and panels, home made. I love the way it looks now. The wish list for me to complete the room is crown molding! Your work looks terrific.

 

[OldManModeler]

Here is what i have been doing the last few days. Had a leak in the RV and had to remove the insulation and do some repairs in the wall. I removed the fiber insulation and installed foam insulation which will not absorb water. Water is deadly to an RV.

I also took the time to build a modeling paint rack and with the extra room im adding some shelves and a small peg board area.

View attachment 126818View attachment 126819View attachment 126820View attachment 126821View attachment 126822


Used to be storage cabinet on the wall but since the fake wood paper on it is peeling im going to use that for my shop and put up some shelves in its place. I also have my eye on a print (painting) to put in the framed space.

I can do plumbing, electrical, structural walls and concrete, at the handyman level. I could probably build my own home for the most part if i was in better health, but i would have to hire out for HVAC i cant do that stuff. Worked alot around construction in my life and im not a contractor by far but i have alot of mixed knowledge. One of my projects comming up is running the electrical to my new shop, and installing the sub panel myself.

In my free time I fix my RV too. Among other things. Like building plastic and RC models.

I am on the US side of the ponds, (east or west), and also a facility manager of a smallish corporation. I work with US type 110-120, 240-277 and 480 volts AC systems. I know just enuf to stay alive, but that's todays forecast. I might be dead tomorrow from electrocution. LOL. If you are Euro, then I cannot help. Those chaps do it all bass-ackward. But if you are US based I might be able to help you.

 

[BarleyBop]

The wish list for me to complete the room is crown molding

Go for it! Our latest renos saw us try different treatments, small through to bigger compound moulding, built up with smaller pieces.

Take your time! Prime and paint before putting up, DAP is your friend!

And if you haven't already, learn how to use that coping saw!

This was the most challenging: I've always loved coffered ceilings, so we went with a simple faux coffered that isn't too heavy for our small dining room. We did try painting the blue between the crown and the smaller trim, but it was too much.

 

[Steve Ski]

Precision work does take time to learn all the little tricks, but minus the gap, this looks good from here. And look at all the money you saved doing it yourself, can't beat it!

When my wife insisted on a new kitchen, I listened up,.......................after 12yrs. Besides, I owed the dogs back rent anyway. When I retired, I bought myself a Grissly table saw, Dewalt planer, and a bunch of extra tools needed to do this kitchen, plus the material at a discount. I saved a ton of cash and my wife and I did the build and install.

And remember, YT is your friend!