Stripper advice

[Edbert]

I'm finally feeling the urge to fix the paint job on the F-16 I nearly ruined last summer.

I seem to recall that Easy-Off oven cleaner was safe to use on plastic models to strip the paint. Not sure if that is right, but even if it is true it might not be the best option.

Would a cloth soaked in alcohol be a better or safer proposition? The paints are mixed, Tamiya XF base, AK clearcoat, oil and enamel wash on top. Plus there are some decals. Not that I want to save the decals (impossible I'd think) but I bought a decal sheet to use once I fix my mistake.

 

[urumomo]

Soak it in Super Clean .
same sodium hydroxide as in oven cleaner but less concentrated and you can reuse the stuff

 

[Greysteele]

My strategy is to start with the weakest solvent and work up to whatever works, even if it's slow. I've had good results soaking a model overnight in a container or ziplok bag full of isopropyl alcohol (70% works). It even removed Tamiya Fine White Primer.

 

[Pantherman]

I'm finally feeling the urge to fix the paint job on the F-16 I nearly ruined last summer.

I seem to recall that Easy-Off oven cleaner was safe to use on plastic models to strip the paint. Not sure if that is right, but even if it is true it might not be the best option.

Would a cloth soaked in alcohol be a better or safer proposition? The paints are mixed, Tamiya XF base, AK clearcoat, oil and enamel wash on top. Plus there are some decals. Not that I want to save the decals (impossible I'd think) but I bought a decal sheet to use once I fix my mistake.

Hoping for something different after reading the title........Pantherman

 

[OldManModeller]

I have used Easy Off oven cleaner to strip chrome off of plastic and nylon parts, and it works perfectly. Many times.

But on an already built kit, I don't know.

Wear gloves and a mask.

 

[Eagle-1]

Walmart.

$10.00 a gallon.



Sink the whole model in a tub of it overnight and tomorrow, it'll be stripped clean. Won't hurt any plastic part even the canopy. You got decals on it already, they'll be gone. Any chrome will be gone in 2 minutes.

Purple Power, right next to this jug in Walmart but cheaper...

AIN'T this.

Rob.

 

[Edbert]

Thanks for all the Super Clean recommendations, from some time spent on youtube it appears to be a standard go-to.

However...
It looks like submersion is a requirement. Most say 24 hours, some say (and show) that it takes 72 hours to get everything out of the panel lines.

That is a problem...
I was needing something I can apply by spray or brush or towel, perhaps I need to explain better.

I ruined a paint job several months ago. My wash technique is that of a newbie, and I ate through or dissolved my base layer down to the lacquer-primer layer. I was hoping to remove the paint without harming the cockpit and to a lesser degree the landing gear and bays.

Here's the thread, and since you don't need to read all that, here's some pics showing why I cannot submerge the entire thing.


The light gray in the 2nd pic is artist-oil. When trying to use thinner to remove the excess I wore down the color-layer as seen near the radome. I'm hoping to spray the thing with the cleaner, and do it daily for however many days it takes to not ruin the cockpit. In fact, I'm considering post-shading and cleanup with an airbrush. It might be the best route. As I mentioned, the decals are done, in fact some are damaged already.

 

[the Baron]

Stripper advice?

Hand-to-hand tipping only.

Seriously, though, I use SuperClean, too. I have not found it necessary to soak a piece for day, but the longer a piece soaks, the more paint will dissolve into the solution, and the remnant softens enough to be scrubbed away gently with an old toothbrush. I have never had SC attack styrene. The active ingredient is lye, which is the same active ingredient in oven cleaners. You should work in a well-ventilated area with either oven cleaner or SuperClean, but the fumes from oven cleaner seem to be stronger.

The advantage over oven cleaner is that you can use a batch of SuperClean over and over, while oven cleaner is basically once-and-done. Though some had said they sprayed oven cleaner into a plastic bag, like a ziploc bag. But it's hard to re-use a batch. But you can put SuperClean in glass containers of various sizes and re-use the batch over and over. So ultimately, it's cheaper for the amount than oven cleaner.

I use it primarily to strip paint from white metal figures, but have also used it on styrene pieces and resin. Apart from soaking a piece, you can also use an old paintbrush to apply it to precise areas. I have done this on models, and on figures, where I made a mistake but didn't want to strip the entire piece and start over.

 

[Eagle-1]

I brush it on all the time. Sponge it, dip it, spray it through a spray bottle and use a toothbrush or paint brush, whatever. Get it on there and re-wet it ever few minutes... same thing. It works until you wash it off with water. It's biodegradable, so wash it in your sink. Strain all the grenubbles out of it and re-use it over and over. Soaking/submersion is just an option and shows that it won't do any harm to any plastic. It won't do a thing to clear parts. I left an assembled 1/25 TAMIYA Chieftain Tank in a tub of it for over a year for a write up on it years ago. No damage at all to even the rubber track pad parts on the plastic tracks. I've been using it for at least 25-30 years.

I see your pictures and although submersion is by no means a requirement, I also don't see any reason you can't submerge that whole thing. Submerging just makes it easier. It'll be back to bare plastic and the canopy won't have a blemish (from the SuperClean at least) on it. The decals will be gone though, but everything else will be bare, box, plastic. Don't use it if you don't want to start over from bare plastic. I can't say I've ever tried to just do a section, so milage may vary.

It's caustic, so were gloves. Not nitrile or latex. Use thicker dish washing gloves. Rinse it with copious amounts of water after the paints gone.

It's $10.00 a gallon. Soak the whole thing for 15 minutes and see what happens. Go from there.

Rob.

 

[urumomo]

That Super Clean is a pretty weak solution of sodium hydroxide so nothing important will be happening , but you should not store sodium hydroxide in glass containers -- it likes to dance with the silica .
Just a heads up if someone is considering storing a stronger lye solution in a glass container .

But you can put SuperClean in glass containers of various sizes

 

[Eagle-1]

but have also used it on styrene pieces and resin.

Like the Baron just said, I use it for everything too, but be aware of resin, in my experience only. It will start to soften the outer layers of resin. After a day of soaking resin, be very careful with a toothbrush because you can start to dig in a little and leave the brush marks. A couple hours, fine, scrub away, but resin does start to soften over soakage time. It has always stiffened back up after a few hours, but straight out of the cleaner after a day and it'll have a soft skin.

It don't work on you model? Ok, clean your engine or oil spots off your driveway.

A win/win city-ation.

Rob.

 

[Edbert]

That Super Clean is a pretty weak solution of sodium hydroxide so nothing important will be happening , but you should not store sodium hydroxide in glass containers -- it likes to dance with the silica .
Just a heads up if someone is considering storing a stronger lye solution in a glass container .

I understood little of that, but having made soap as a lad (once) I have a massive respect for lye.

 

[TimM63]

This is not what I expected when I read the title of this thread. LOL